Black Box Compact T1 MT850A User Manual Download

Page: 376 / 592

6-6

Compact T1 - Release 6.1

T1 Controller Card

Technical Specifications

Service Interfaces Supported

IP Router card (supports up to 24 WAN connections per card)

Customer Media Gateway (CMG) Service card (to support VoIP)

FXO/DPT 8-channel Voice Service card

FXS 8-channel Voice Service card

ISDN BRI 2, 4 and 8-channel Service cards

Dual V.35 and Dual V.35/V.54 Service cards

Quad T1 Network Access/Drop-and-Insert Service card

OCU-DP Single and 4 port Service cards

Network Standards

AT&T Pub 54016, TR 62411

ANSI T1-403, T1.102, T1.231

Clocking

Loop-timed from any T1

Revertive clock switching provides automatic backup to secondary T1 should the
primary T1 fail

Operates as a Stratum 4E device

Alarms

One major and one minor alarm output

One alarm input

Alarm contacts accessible from external alarm connector

All alarms are logged in an event log

Loss of AC power triggers minor alarm

Generates SNMP traps for alarming (MIB objects)

Summary of Contents for Compact T1 MT850A
















































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Compact T1 MT850A

Reviews:

Related manuals for Compact T1 MT850A

Brands by name

Popular brands

Black Box Compact T1 MT850A, User Manual

Search results

Summary of Contents for Compact T1 MT850A

Reviews:

Related manuals for Compact T1 MT850A

Brands by name

Popular brands