manualshive.com logo in svg

Black Box Compact T1 MT850A, User Manual

Looking for a user manual for the Black Box Compact T1 MT850A? Look no further! Download your free manual from manualshive.com and make the most out of this exceptional product. Gain valuable insights and unleash the full potential of your Black Box Compact T1 MT850A with our comprehensive user manual.

Share
Download
background image

5-214

Compact T1 - Release 6.1

CLI Commands

show

show impedance

The show impedance command displays the impedance settings for FXS 5G card.

Syntax:

show impedance

Example:

show impedance                      

 Index             Impedance             CODEX        Country

 -----  -------------------------------  -----  -------------------

   1    120 Ohms + (.110

µ

F || 820 Ohms)  A-law   Norway

   2    150 Ohms + (.047

µ

F || 510 Ohms)  A-law   Malaysia

   3    150 Ohms + (.072

µ

F || 830 Ohms)  A-law   Belgium

   4    200 Ohms + (.100

µ

F || 680 Ohms)  A-law   China

   5    215 Ohms + (.137

µ

F || 1k  Ohms)  A-law   France

   6    220 Ohms + (.115

µ

F || 820 Ohms)  A-law   Austria, Germany,

                                                 Mexico, Switzerland

   7    220 Ohms + (.120

µ

F || 820 Ohms)  A-law   Australia

   8    270 Ohms + (.120

µ

F || 910 Ohms)  A-law   Finland

   9    300 Ohms + (.220

µ

F || 1k  Ohms)  A-law   United Kingdom

  10    370 Ohms + (.310

µ

F || 620 Ohms)  A-law   New Zealand

  11    400 Ohms + (.033

µ

F || 500 Ohms)  A-law   Denmark

  12    400 Ohms + (.050

µ

F || 500 Ohms)  A-law   Greece

  13    600 Ohms                         A-law   Korea, Indonesia,

                                                 Italy, Poland,

                                                 Russia, Spain,

                                                 Thailand, China

  14    600 Ohms + 1.00

µ

F                

µ

-law   Japan

  15    600 Ohms + 1.50

µ

F                A-law   Saudi Arabia

  16    600 Ohms + 2.16

µ

F                

µ

-law   Korea

  17    800 Ohms                         A-law   Netherlands

  18    900 Ohms                         A-law   Brazil

  19    900 Ohms + 2.16

µ

F                

µ

-law   USA, Taiwan

Note: In general, 

µ

-Law settings are used for T1 applications, A-Law settings are used for 

E1 applications.

Summary of Contents for Compact T1 MT850A

















































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Compact T1 MT850A

Samson 6616-0000 Mounting And Operating Instructions preview
6616-0000
Brand: Samson Pages: 70
Teltronika FMC225 Quick Manual preview
FMC225
Brand: Teltronika Pages: 18
National Instruments TBX-68S Installation Manual preview
TBX-68S
Brand: National Instruments Pages: 8
123SEND AXEPT S800 Quick Start Manual preview
AXEPT S800
Brand: 123SEND Pages: 20
Kestronics SC600 User Manual preview
SC600
Brand: Kestronics Pages: 40
Omron B7A Manual preview
B7A
Brand: Omron Pages: 121
BUSIN TD5-C2 User Manual preview
TD5-C2
Brand: BUSIN Pages: 17
Janus POTSwap EVDO910PS User Manual preview
POTSwap EVDO910PS
Brand: Janus Pages: 20
WideFly WF360ST Quick Start Manual preview
WF360ST
Brand: WideFly Pages: 16
FITX ON-DEMAND FITNESS FITX Quick Start Manual preview
FITX
Brand: FITX ON-DEMAND FITNESS Pages: 5
3nStar J4125 User Manual preview
J4125
Brand: 3nStar Pages: 14
ABNICS FT23D User Manual preview
FT23D
Brand: ABNICS Pages: 57
Landi E830 User Manual preview
E830
Brand: Landi Pages: 18
UniGuard UM405 User Manual preview
UM405
Brand: UniGuard Pages: 4
EC Line EC-VP-1100 Instructions For Assembly/Disassembly preview
EC-VP-1100
Brand: EC Line Pages: 7
ZKTeco ZPAD+ User Manual preview
ZPAD+
Brand: ZKTeco Pages: 50
Unitech Tashi Quick Reference Manual preview
Tashi
Brand: Unitech Pages: 49
Festo VTSA ASI-8E8A-Z Series Brief Description preview
VTSA ASI-8E8A-Z Series
Brand: Festo Pages: 86

Brands by name

Popular brands

Load more brands