Black Box Compact T1 MT850A User Manual Download

Page: 379 / 592

Compact T1 - Release 6.1

6-9

T1 Controller Card

Configuration

DIP Switch Settings

On the front of the TDM Controller card are DIP switches you can use to configure the
unit locally.

Switch

Function

Description

ACO

Alarm Cut
Off

0 = Alarm contacts enabled (close when alarm occurs).
Default.
1 = Alarm contacts disabled (open).

Self Test

0 = Normal operation. Default.
1 = Perform Self Test.

OPT

Spare

RST

Reset

0 = User-configured operation. Default.
1 = Reset configuration to factory defaults, and reset CLI
password.

T1-1
T2-1

Line Coding

0 = B8ZS. Default.
1 = AMI

T1-2
T2-2

Line
Loopback

0 = Loopback off. Default.
1 = Loopback on

T1 3-4
T2 3-4

Framing

0 = ESF (Extended Superframe). Default.
1 = D4

T1 5 - 6
T2 5 - 6

Signaling

Switch 3

Switch 4

Switch 5

Switch 6

Setting

TR-08 A-Shelf with FDL, 16-bit Alarm frame

TR-08 A-Shelf with FDL, 13-bit Alarm frame

TR-08 A-Shelf with FDL disabled

TR-08 B-Shelf

Loop Start/Ground Start. Default.

E&M Immediate Start with ringback. (used for D3 PLAR
and DPT)

E&M Immediate Start with ringback and Calling Party
Disconnect (CPD)

Summary of Contents for Compact T1 MT850A
















































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Compact T1 MT850A

Reviews:

Related manuals for Compact T1 MT850A

Brands by name

Popular brands

Black Box Compact T1 MT850A, User Manual

Search results

Summary of Contents for Compact T1 MT850A

Reviews:

Related manuals for Compact T1 MT850A

Brands by name

Popular brands