Black Box Compact T1 MT850A User Manual Download

Page: 485 / 592

Compact T1 - Release 6.1

14-11

Router (CMG) Card

Card Configuration

delete (router-wan) static
Remove a static element from the WAN interface

disconnect {slot:port:trunk}
Removes a connection created by the connect {trunk-addr}{t1-addr}

install (slot) router
Will prepare the controller for the insertion of a new router card that will
keep its currently loaded configuration

load tftp
Will download software via TFTP to the Controller or the Router card

rename (router) (router-wan/lan)
Change the name of a remote WAN or local LAN profile on the Router card

reset (router)
Reboot the Router. All new configuration since the last configuration will be
in-use

rtrping
Router will perform a ping test and report the result.

set (router) autologout
Set the period of time on inactivity after which the user will be automatically
logged-out of a Telnet session

set (router) cdr
Enable/disable Call Detail Recording (CDR) for the CMG card

set (router) compander
Set the companding algorithm to use with the PCM (G.711) voice stream
to/from the TDM side of a connection

set (router) default
Reset the Router card to its default configuration settings

set (router) dhcp
Configure the DHCP functions

set (router) dns
Set the CMG Domain Name Server (DNS) options

set (router) enhanced security
Enable/disable enhanced login security on the Router

set (router) hookflash
Specify the flash maximum time

Summary of Contents for Compact T1 MT850A
















































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Compact T1 MT850A

Reviews:

Related manuals for Compact T1 MT850A

Brands by name

Popular brands

Black Box Compact T1 MT850A, User Manual

Search results

Summary of Contents for Compact T1 MT850A

Reviews:

Related manuals for Compact T1 MT850A

Brands by name

Popular brands