Equinox Payments
9045 E. Pima Center Pkwy, Suite 3, Sco sdale, AZ 85258, USA | Tel: +1.877.497.3726 | Fax: +1.480.551.7811 | www.EquinoxPayments.com
© 2013-2014 Equinox Payments, all rights reserved. Equinox Payments and the Equinox Payments logo are registered trade-
marks of Equinox Payments. Informa on within this guide may not match the terminal device and its accessories exactly and
thus are subject to change. 940649-001E Rev. C 09/14
INSTALLATION GUIDE
APOLLO CFD
INSTALLATION GUIDE
APOLLO CFD
WARNING
•
Only use the provided Equinox Payments A/C Power Adapter.
Non-compliant power adapters may damage the device.
•
Do not use if visibly damaged.
•
Do not expose to temperatures below -10 °C or above 60 °C
storage (not powered).
•
Intended operating humidity range is 5% to 95% rh (non-condensing).
•
Do not disassemble.
•
Do not incinerate or crush.
•
This device is not designed or cer
fi
ed to be used in a
fl
ammable atmosphere such as a petrol sta on or chemical
depot where there is a risk of explosion.
•
Keep out of reach of children or pets.
•
Only use your
fi
nger on the display. Do NOT use a pen,
pencil or hard p stylus for it WILL damage the display and
void the warranty.
SAFETY INFORMATION
The Apollo family of devices must be used within the opera ng
condi ons, electrical supply requirements, environmental
condi ons and connec on requirements as speci
fi
ed below:
•
Power Supply: These devices must be connected to the
correct electrical supply. Connec on to an inappropriate
supply may damage or destroy this device(s), thereby
invalida ng its warranty(s).
•
Only operate these devices within the temperature range of
0 °C - 45 °C.
•
Hazardous Environments: These devices must NOT be
installed in loca ons where there is danger of explosion.
COMPLIANCE
Changes or modi
fi
ca ons not expressly approved by the party
responsible for compliance could void the user’s authority to
operate the equipment.
•
FCC Part 15
This equipment has been tested and found to comply with the
limits for a Class A digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protec-
on against harmful interference when the equipment is
operated in a commercial environment. This equipment gen-
erates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instruc on manual,
may cause harmful interference to radio communica ons.
Opera on of this equipment in a residen al area is likely to
cause harmful interference in which case the user will be
required to correct the interference in which case the user will
be required to correct the interference at his own expense.
The user is cau oned that changes or modi
fi
ca ons not ex-
pressly approved by the party responsible for compliance
could void the user’s authority to operate this device.
•
UL/cUL Listed
•
FCC ID: NVA00008
•
FCC Part 68
This device complies with Part 68 of the FCC rules and the
requirements adopted by the ACTA. On the underside of this
device is a label that contains, among other informa on, a
product iden
fi
er in the format US:AAAEQ##TXXXX.
If requested, this number must be provided to the telephone
company.
A plug and jack used to connect this device to the premises
wiring and telephone network must comply with the applicable
FCC Part 68 rules and requirements adopted by the ACTA. A
compliant telephone cord and modular plug is provided with
this device. It is designed to be connected to a compa ble
modular jack that is also compliant.
The REN is used to determine the number of devices that may
be connected to a telephone line. Excessive RENs on a tele-
phone line may result in the devices not ringing in response to
an incoming call. In most but not all areas, the sum of RENs
should not exceed
fi
ve (5.0). To be certain of the number of
devices that may be connected to a line, as determined by the
total RENS, contact the local telephone company. The REN for
this device is part of the product iden
fi
er that has the format
US:AAAEQ##-TXXXX, where the digits represented by ## are
the REN without a decimal point (e.g., 03 is a REN of 0.3). If this
device causes harm to the telephone network, the telephone
company will no fy you in advance that temporary discon nu-
ance of service may be required. But if advance no ce isn’t
prac cal, the telephone company will no fy the customer as
soon as possible. Also, you will be advised of your right to
fi
le
a complaint with the FCC if you believe it is necessary.
The telephone company may make changes in its facili es,
equipment, opera ons or procedures that could a
ff
ect the
opera on of this device. If this happens, the telephone compa-
ny will provide advance no ce in order for you to make neces-
sary modi
fi
ca ons to maintain uninterrupted service.
If trouble is experienced with this device, please contact
Equinox Payments at 1.877.497.3726 for repair or warran-
ty informa on. If this device is causing harm to the tele-
phone network, the telephone company may request that
you disconnect this device un l the problem is resolved.
The user is not authorized to perform any service of this device.
Connec on to party-line service is subject to state tari
ff
s.
Contact the state public u lity commission, public service
commission, or corpora on commission for informa on.
940649-001E
SHIPPING
CONTENTS*
Addi onal cables
available for purchase:
•
RS232 cable
•
Ethernet cable
•
MFD to AIO/CFD cable
(810417-002E)
•
CFD/MFD Mono cable
(810418-002E)
RJ11 Cable (Line)
(810005-010)
A/C Power Adapter
(870082-10XE)
Apollo CFD Terminal
(020372-00XE)
*Contents may not exactly match
CAUTION
To reduce the risk of
fi
re, use only No. 26 AWG or larger (e.g., 24 AWG) UL Listed or CSA Cer
fi
ed Telecommunica on Line Cord.
