manualshive.com logo in svg

Black Box Compact T1 MT850A, User Manual

Looking for a user manual for the Black Box Compact T1 MT850A? Look no further! Download your free manual from manualshive.com and make the most out of this exceptional product. Gain valuable insights and unleash the full potential of your Black Box Compact T1 MT850A with our comprehensive user manual.

Share
Download
background image

5-244

Compact T1 - Release 6.1

CLI Commands

show

show (router-wan) static ip address

The show (router-wan) static ip address command displays the current list of static IP address 
entries for the specified WAN interface.

Syntax:

show {rtr_card-addr} {"wan-name"} static ip address

Example:

show 5 "LosAngeles" static ip address

> show 5 "LosAngeles" static ip address

SLOT 5:

WAN Static IP Address Settings for LosAngeles:

    Total: 0        

                                                 

{rtr_card-addr}

The slot number (1-6) that contains the Router (IP or CMG) card.

{"wan-name"}

The WAN interface to modify. The name must be enclosed in quotes.

show (router-wan) static ip network

The show (router-wan) static ip network command displays the current list of static IP 
network entries for the specified WAN interface.

Syntax:

show {rtr_card-addr} {"wan-name"} static ip network

Example:

show 5 "LosAngeles" static ip network

> show 5 "LosAngeles" static ip network

SLOT 5:

WAN Static IP Network Settings for LosAngeles:

    Network           Subnet Mask       Metric   Remote Tunnel Addr

    200.1.1.0         255.255.255.0     1

    Total: 1

                                                                                                                                

{rtr_card-addr}

The slot number (1-6) that contains the Router (IP or CMG) card.

{"wan-name"}

The WAN interface to modify. The name must be enclosed in quotes.

Summary of Contents for Compact T1 MT850A

















































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Compact T1 MT850A

EC Line EC-VP-1100 User Manual preview
EC-VP-1100
Brand: EC Line Pages: 23
EBN Technology EZPOS70-2B-C1G Service Manual preview
EZPOS70-2B-C1G
Brand: EBN Technology Pages: 21
HIKVISION DS-K1T8003 Series Quick Start Manual preview
DS-K1T8003 Series
Brand: HIKVISION Pages: 2
EBN Technology TM-70 Service Manual preview
TM-70
Brand: EBN Technology Pages: 19
Schlage HK-CR User Manual preview
HK-CR
Brand: Schlage Pages: 88
Titus DLSC Installation, Operation And Maintenance Manual preview
DLSC
Brand: Titus Pages: 17
Appostar KP-5660 User Manual preview
KP-5660
Brand: Appostar Pages: 28
Advantech WebOP-3000 Series Installation Manual preview
WebOP-3000 Series
Brand: Advantech Pages: 4
Ingenico i8550 Specifications preview
i8550
Brand: Ingenico Pages: 2
Inepro PayMatic 4B - Xerox MFP Install Manual preview
PayMatic 4B - Xerox MFP
Brand: Inepro Pages: 12
Yamatake EST240Z User Manual preview
EST240Z
Brand: Yamatake Pages: 64
Vector OPU-D42-W50 Operation Manual preview
OPU-D42-W50
Brand: Vector Pages: 2
ESA VT505W Manual preview
VT505W
Brand: ESA Pages: 6
Ingenico group iSMP v4 Wi-Fi Manual preview
iSMP v4 Wi-Fi
Brand: Ingenico group Pages: 23
Zenith ZTX-10 Series User Manual preview
ZTX-10 Series
Brand: Zenith Pages: 60
Vector Graphic Mindless User Manual preview
Mindless
Brand: Vector Graphic Pages: 72
Qume QVT-108 Operator'S Manual preview
QVT-108
Brand: Qume Pages: 94
QUORION QTOUCH PC User Manual preview
QTOUCH PC
Brand: QUORION Pages: 30

Brands by name

Popular brands

Load more brands