Black Box Compact T1 MT850A User Manual Download

Page: 345 / 592

Compact T1 - Release 6.1

5-261

CLI Commands

status

status (fxs5G)

Use the status (fxs5G) to display the current near-end line status of the specified FXS 5G card.

Syntax:

status {fxs5G-addr}

Example:

status 4:1

The example displays status of port 1 (FXS 5G) on slot 4.

> status 4:1

FXS Rx AB Tx AB Signal=>T1 Sig T1 TP

--- ----- ----- -------------- ----------------- --

4:1 01 01 LS => LS Traffic N

{fxs5G-addr}

Display Descriptions

DS0 -

Identifies location of DS0

Rx AB - AB bits received by the FXS or FXO port (real-time)

Tx AB - AB bits transmitted by the FXS or FXO port (real-time)

Signal - Signaling mode for which the FXS or FXO port is configured

T1 - Status of the T1 (Traffic, Loss of Signal, Loss of Framing, Loopback)
TP -

Trunk Processing (Y = yes, N = no)

slot

The slot number (1-6) that contains the FXS 5G card

port

Port number or range.

Set to Ground Start signaling

gsrb

Set to Ground Start signaling with reverse battery

gsw

Set to Ground Start Wink signaling

gswb

Set to Ground Start Wink signalling with reverse battery

Set to Loop Start signaling

lsrb

Set to Loop Start signaling with reverse battery

Summary of Contents for Compact T1 MT850A
















































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Compact T1 MT850A

Reviews:

Related manuals for Compact T1 MT850A

Brands by name

Popular brands

Black Box Compact T1 MT850A, User Manual

Search results

Summary of Contents for Compact T1 MT850A

Reviews:

Related manuals for Compact T1 MT850A

Brands by name

Popular brands