Black Box Compact T1 MT850A User Manual Download

Page: 76 / 592

4-14

Compact T1 - Release 6.1

Configuration

Quick Configuration Reload

3. Select the ASCII Setup button.

4. Set the Line delay to 50 milliseconds and the Character delay to 5

milliseconds.

5. Select the [OK] button back to the Main HyperTerminal screen.

6. Select Transfer/Send Text File.. from the menu bar.

Hyperterm will now send the configuration to the Adit exactly as it was saved in
the Download Config File process.

Summary of Contents for Compact T1 MT850A
















































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Compact T1 MT850A

Reviews:

Related manuals for Compact T1 MT850A

Brands by name

Popular brands

Black Box Compact T1 MT850A, User Manual

Search results

Summary of Contents for Compact T1 MT850A

Reviews:

Related manuals for Compact T1 MT850A

Brands by name

Popular brands