Black Box Compact T1 MT850A User Manual Download

Page: 501 / 592

Compact T1 - Release 6.1

15-3

V.35/V.54 Cards

Features

Features

Provides any n x 56/64 Kbps data rate up to 1.536 Mbps on each port

Supports full non-blocking cross-connection of all timeslots to any T1 access line

Enables up to 12 V.35 ports may be equipped in a single Compact T1

Allows a total of 24 V.35 ports to be equipped in two Compact T1, occupying
only two rack units of equipment space in a 19-inch rack

Includes integration of T1 CSU/DSU functionality and remote management
capabilities

Supports adaptation and transport over TDM facilities

Integrates frame relay or private line V.35 services with voice and Internet access
over T1 lines

Additional V.54 Features

V.54 Loop Test capability

Technical Specifications

Controller Software Required

T1 Controller

Release 1.2.2 or higher is required for the V.35 card

Release 3.0 or higher is required for the V.35/V.54 card

Service Interface

Two V.35 interfaces:

DCE to DTE pinout

Two sub-miniature DB-26 connectors

Adapters outlined below

Summary of Contents for Compact T1 MT850A
















































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Compact T1 MT850A

Reviews:

Related manuals for Compact T1 MT850A

Brands by name

Popular brands

Black Box Compact T1 MT850A, User Manual

Search results

Summary of Contents for Compact T1 MT850A

Reviews:

Related manuals for Compact T1 MT850A

Brands by name

Popular brands