Bittium NeurOne User Manual Download Page 32

Page: 32 / 191

Page 32 of 191

800581-2.11 NeurOne System User Manual.doc

4.1 Main Unit

– model Extended

The front panel of the Main Unit has following components:

Audio Out

–

3.5 mm connector for headphones in audio applications.

Speaker

–

Speaker for audio applications.

Display

–

Display for measurement information and device diagnostic purposes.

Power On Led (ON)

–

Indicates that the Main Unit is operational.

Power Indicator Led (AC)

–

Indicates that the Main Unit is connected to mains

power (green).

Power Button (green)

–

ON/OFF-switch, selecting display mode



Default mode “NeurOne, press button for info”





Tesla amplifier voltages





Trigger counters





SyncBox info





Digital Out info





CPU loads of EXG/Tesla amplifiers





Firmware upgrade



Summary of Contents for NeurOne
































































































































































































Search results

Summary of Contents for NeurOne

Reviews:

Related manuals for NeurOne

Brands by name

Popular brands

Bittium NeurOne, User Manual

Search results

Summary of Contents for NeurOne

Reviews:

Related manuals for NeurOne

Brands by name

Popular brands