Bittium NeurOne User Manual Download Page 167 | Manualshive

Page: 167 / 191

background image

Page 167 of 191

800581-2.11 NeurOne System User Manual.doc

If Bipolar Connection Box default or current (previously changed) configuration will be
changed / checked, the following configuration steps shall be complied with:

1. Only authorized and trained person is allowed to perform the configuration of

Bipolar Connection Box. The person must be trained by Bittium Biosignals Ltd
or the official local distributor of Bittium Biosignals Ltd.

2. Disconnect Bipolar Connection Box from the NeurOne system and reserve

small screwdriver, one Bipolar Connection Box Adhesive Configuration
Template sticker (800852) and marking pen for configuration change/check
procedure.

3. Turn the Bipolar Connection Box rear side up. Open two plastic screws and

disconnect the bottom lid and flip it on long side as shown on the photo below.

4. Keep Adhesive Configuration Template sticker beside the opened Bipolar

Connection Box while making the changes/check to configuration.

«
...
165
166
167
168
169
...
»

Summary of Contents for NeurOne
































































































































































































Reviews:

No comments

Related manuals for NeurOne

Brand: IBS Scherer Pages: 64

Brand: Jackco Pages: 6

Brand: h/p/cosmos Pages: 81

Brand: K-9 Lights Pages: 12

ProFire Lightbridge

Brand: M-Audio Pages: 8

Brand: M-Audio Pages: 36

Brand: MAHA Pages: 21

Brand: MAGUIRE Pages: 47

Brand: Omlet Pages: 2

Brand: Omicron Pages: 382

Brand: Omicron Pages: 188

Brand: Qlight Pages: 3

Brand: qtran Pages: 2

Brand: Q-Optics Pages: 2

Brand: TATU Pages: 30

Brand: Rane Pages: 4

Brand: Sabio Pages: 182

Brand: ValueStore US Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands