Big Backyard ASHBERRY II F23073C Installation And Operating Instructions Manual Download Page 39

Page: 39 / 80

[email protected]

Step 11: Swing Wall Assembly

Part 2

1 x

1/4 x 2” Hex Bolt (1/4” lock washer, 1/4” flat washer, 1/4” t-nut)

4 x

1/4 x 3” Lag Screw (1/4” flat washer)

1 x

1/4 x 2-1/2” Lag Screw (1/4” flat washer)

2 x

Gusset II 5/4 x 4 x 18-1/2”

1 x

Lower Diagonal 2 x 3 x 37”

2113

0369

Note: Pre-drill all holes using a 3/16” drill bit before installing the lag screws.
D:

Attach (0369) Lower Diagonal to the end of (2157) Ground SW Side on the Front Wall side with 1 (H2) 1/4 x

2” Hex Bolt (with lock washer, flat washer and t-nut) and to (2153) Post with 1 (LS2) 1/4 x 2-1/2” Lag Screw (with

flat washer). (fig. 11.2)

Tight to the bottom of (2126) SW Floor and bevelled edges flush to outside edge of (2153) Posts, attach 1

(2113) Gussett II to each side using 2 (LS3) 1/4 x 3” Lag Screws (with flat washer) per gusset. (fig. 11.2)

Hardware

Wood Parts

1/4” lock

washer

1/4” flat

washer

1/4”

t-nut

Fig. 11.2

2153

1/4” flat

washers

LS3

LS2

2126

2113

0369

LS2

LS3

2157

Front Wall

Flush

1/4” flat

washer

Summary of Contents for ASHBERRY II F23073C

















































































Search results

Summary of Contents for ASHBERRY II F23073C

Reviews:

Related manuals for ASHBERRY II F23073C

Brands by name

Popular brands

Big Backyard ASHBERRY II F23073C, Installation And Operating Instructions Manual

Search results

Summary of Contents for ASHBERRY II F23073C

Reviews:

Related manuals for ASHBERRY II F23073C

Brands by name

Popular brands