Big Backyard ASHBERRY II F23073C Installation And Operating Instructions Manual Download Page 37

Page: 37 / 80

[email protected]

Attach (2143) Middle Back, on the outside of the assembly to both (2153) Posts with 2 (H2) 1/4 x 2” Hex Bolts

(with lock washer, flat washer and t-nut). (fig. 10.3)

Make sure the assembly is square then tighten all bolts and attach (2143) Middle Back to each (2153) Post

with 2 (S15) #8 x 1-3/4” Wood Screws. (fig. 10.3)

At the ends of (2143) Middle Back and (2120) Floor Front Back place (2112) SL Post, as shown in fig. 10.3.

Attach (2112) SL Post to (2123) Back Floor with 1 (H5) 1/4 x 4-1/2” Hex Bolt (with lock washer, flat washer and

t-nut) and to (2143) Middle Back with 1 (H4) 1/4 x 4” Hex Bolt (with lock washer, flat washer and t-nut) in the top

hole and 1 (S7) #12 x 2” Pan Screw (with flat washer) in the bottom hole. (fig. 10.3)

Attach (2112) SL Post to (2120) Floor Front Back with 2 (S4) #8 x 3” Wood Screws. (fig. 10.3)

Hardware

Wood Parts

1 x

Middle Back 1 x 5 x 65-5/8”

1 x

SL Post 2 x 4 x 32-1/2”

2143

2112

Step 10: Back Wall Assembly

Part 2

2123

2153

1/4” lock

washer

1/4” flat

washer

1/4”

t-nut

Outside View

2143

Fig. 10.3

S15

2120

2112

with 3/16”

flat washer

1/4” lock

washer

1/4” flat

washer

1/4”

t-nut

2 x

#8 x 1-3/4” Wood Screw

1 x

#12 x 2” Pan Screw (3/16” flat washer)

2 x

#8 x 3” Wood Screw

2 x

1/4 x 2” Hex Bolt

(1/4” lock washer, 1/4” flat washer, 1/4” t-nut)

1 x

1/4 x 4” Hex Bolt

(1/4” lock washer, 1/4” flat washer, 1/4” t-nut)

1 x

1/4 x 4-1/2” Hex Bolt

(1/4” lock washer, 1/4” flat washer, 1/4” t-nut)

S15

Summary of Contents for ASHBERRY II F23073C

















































































Search results

Summary of Contents for ASHBERRY II F23073C

Reviews:

Related manuals for ASHBERRY II F23073C

Brands by name

Popular brands

Big Backyard ASHBERRY II F23073C, Installation And Operating Instructions Manual

Search results

Summary of Contents for ASHBERRY II F23073C

Reviews:

Related manuals for ASHBERRY II F23073C

Brands by name

Popular brands