Big Backyard ASHBERRY II F23073C Installation And Operating Instructions Manual Download Page 31

Page: 31 / 80

[email protected]

Overlap cedar roofing

2156

1-1/2”

Roof Supports

removed for clarity

Flush to edge

Step 8: Roof Assembly

Part 2

Starting at the top of the Roof Support Assembly attach 1 (2156) Roofing on each side of the Roof Support

Assemblies with 3 (S0) #8 x 7/8” Truss Screws per board. (fig. 8.2) Be sure to overlap the top of the boards so

there are no gaps. (fig. 8.2 and 8.3)

Drill a hole 1-1/2” up from the bottom of the 2 bottom (2156) Roofing (for bottom row only).

Attach 1 (2156)

Roofing at the bottom of the Roof Support Assembly on each side, making sure they are flush to each (2146) Roof

Support Right and (2132) Roof Support Left with 3 (S0) #8 x 7/8” Truss Screws per board. (fig. 8.2 and 8.4)

On one side of the assembly evenly space and attach 8 (2156) Roofing, leaving no gaps, with 3 (S0) #8 x 7/8”

Truss Screws per board. There should be 10 (2156) Siding on this side. (fig. 8.2)

On the other side of the assembly evenly space and attach 8 (2156) Roofing, leaving no gaps, with 3 (S0) #8 x

7/8” Truss Screws per board. (fig. 8.2)

Fig. 8.4

Wood Parts

Hardware

60 x

#8 x 7/8” Truss Screw

20 x

Roofing 3/8 x 3-1/2 x 53-13/16”

2156

Fig. 8.2

Fig. 8.3

2132

2146

1-1/2”

x 60

2156

x 20

2161

(hidden)

Summary of Contents for ASHBERRY II F23073C

















































































Search results

Summary of Contents for ASHBERRY II F23073C

Reviews:

Related manuals for ASHBERRY II F23073C

Brands by name

Popular brands

Big Backyard ASHBERRY II F23073C, Installation And Operating Instructions Manual

Search results

Summary of Contents for ASHBERRY II F23073C

Reviews:

Related manuals for ASHBERRY II F23073C

Brands by name

Popular brands