Big Backyard ASHBERRY II F23073C Installation And Operating Instructions Manual Download Page 61

Page: 61 / 80

[email protected]

Hardware

Wood Parts

From inside the fort measure 13” up from the bottom of (2154) Front Post attach (2107) Door Stop to (2154)

Front Post and (2135) Wall Support with 3 (S15) #8 x 1-3/4” Wood Screws. (fig. 24.5, 24.6 and 24.7)

In the notched out opening of (2107) Door Stop attach the Magnetic Catch using 2 (S18) #6 x 1” Wood Screws.

(fig. 24.6)

Important: Use a hand held screw driver and DO NOT over tighten.

3 x

#8 x 1-3/4” Wood Screw

2 x

#6 x 1” Wood Screw

S15

1 x

Door Stop 5/4 x 4 x 10”

2107

Fig. 24.6

Fig. 24.5

Other Parts

1 x Magnetic Catch

S18

Step 24: Door Wall Assembly

Part 3

Inside View

2154

Outside View

S15

13”

Magnetic Catch

S18

2107

2135

Fig. 24.7

Note: Door Stop should over hang

1-1/4”

in the opening.

Summary of Contents for ASHBERRY II F23073C

















































































Search results

Summary of Contents for ASHBERRY II F23073C

Reviews:

Related manuals for ASHBERRY II F23073C

Brands by name

Popular brands

Big Backyard ASHBERRY II F23073C, Installation And Operating Instructions Manual

Search results

Summary of Contents for ASHBERRY II F23073C

Reviews:

Related manuals for ASHBERRY II F23073C

Brands by name

Popular brands