Big Backyard ASHBERRY II F23073C Installation And Operating Instructions Manual Download Page 43

Page: 43 / 80

[email protected]

Drive 1 (0318) Ground Stake 10-1/2” into the ground on (2157) Ground SW Side at (0369) Lower Diagonal

and 1 on the Slide Wall Side tight to (2153) Post on the Back Wall as shown in fig. 14.1. Attach using 2 (S3)

#8 x 2-1/2” Wood Screws per ground stake. (fig. 14.2)

Wood Parts

Hardware

Fig. 14.1

4 x

#8 x 2-1/2” Wood Screw

2 x

Ground Stake 1-1/4 x 1-1/2 x 14”

0318

Step 14: Attach Ground Stakes

MOVE FORT TO FINAL LOCATION. FINAL LOCATION MUST BE LEVEL GROUND.

WARNING:

To prevent tipping and avoid potential injury, stakes must

be driven 10-1/2” into ground. Digging or driving stakes can be dangerous

if you do not check first for underground wiring, cables or gas lines.

2153

10-1/2” Into Ground

Fig. 14.2

0369

Swing Side

Front Wall

Back Wall

2157

0318

Slide Wall

Summary of Contents for ASHBERRY II F23073C

















































































Search results

Summary of Contents for ASHBERRY II F23073C

Reviews:

Related manuals for ASHBERRY II F23073C

Brands by name

Popular brands

Big Backyard ASHBERRY II F23073C, Installation And Operating Instructions Manual

Search results

Summary of Contents for ASHBERRY II F23073C

Reviews:

Related manuals for ASHBERRY II F23073C

Brands by name

Popular brands