Big Backyard ASHBERRY II F23073C Installation And Operating Instructions Manual Download Page 38

Page: 38 / 80

[email protected]

With at least one adult helper hold up the Front and Back Walls and loosely attach (2157) Ground SW Side

using 4 (H4) 1/4 x 4” Hex Bolts (with lock washer, flat washer and t-nut), (2126) SW Floor using 2 (H5) 1/4 x

4-1/2” Hex Bolts (with lock washer, flat washer and t-nut) in the top holes and (2106) SW Top using 4 (H5) 1/4 x

4-1/2” Hex Bolts (with lock washer, flat washer and t-nut) to both (2153) Posts. (fig. 11.1)

Loosely attach (2130) SW Mount to (2126) SW Floor and to (2106) SW Top with 2 (G5) 5/16 x 4-1/2” Hex

Bolts (with lock washer, flat washer and t-nut). Keep these bolts loose until Step 13, Part 1. (fig. 11.1)

Note: Pre-drill all holes using a 1/8” drill bit before installing the lag screws.
C:

Make sure the assembly is square then tighten all 1/4” Hex Bolts from this step. Attach (2126) SW Floor to

each (2153) Post with 2 (LS3) 1/4 x 3” Lag Screw (with flat washer). (fig. 11.1)

Step 11: Swing Wall Assembly

Part 1

2 x

5/16 x 4-1/2” Hex Bolt (5/16” lock washer, 5/16” flat washer, 5/16” t-nut)

4 x

1/4 x 4” Hex Bolt (1/4” lock washer, 1/4” flat washer, 1/4” t-nut)

6 x

1/4 x 4-1/2” Hex Bolt (1/4” lock washer, 1/4” flat washer, 1/4” t-nut)

2 x

1/4 x 3” Lag Screw (1/4” flat washer)

1 x

SW Top 5/4 x 5 x 38-3/4”

1 x

SW Mount 2 x 4 x 34-1/2”

1 x

SW Floor 5/4 x 5 x 38-3/4”

1 x

Ground SW Side 1 x 5 x 81-1/8”

2106

2126

2130

1/4” lock

washer

1/4” flat

washer

1/4”

t-nut

Hardware

Wood Parts

Fig. 11.1

2106

2126

2157

2130

2153

LS3

2157

LS3

2153

Notice holes towards top.

1/4” flat

washer

5/16” flat

washer

5/16” lock

washer

x 4

Front Wall

Back Wall

5/16”

t-nut

Notice pilot holes are

above bolt hole (not

shown in picture)

Summary of Contents for ASHBERRY II F23073C

















































































Search results

Summary of Contents for ASHBERRY II F23073C

Reviews:

Related manuals for ASHBERRY II F23073C

Brands by name

Popular brands

Big Backyard ASHBERRY II F23073C, Installation And Operating Instructions Manual

Search results

Summary of Contents for ASHBERRY II F23073C

Reviews:

Related manuals for ASHBERRY II F23073C

Brands by name

Popular brands