Big Backyard ASHBERRY II F23073C Installation And Operating Instructions Manual Download Page 72

Page: 72 / 80

[email protected]

Step 34: Slide Support Assembly

Part 2

Fig. 34.2

Fig. 34.3

At the end of (2110) Slide Ground dig

one, flat bottom, 8” wide by 6” deep hole as

shown in fig. 34.3. Place (2137) SL Upright

in the hole, making sure that it is plumb.

Notice the angled edge slopes towards

(2110) Slide Ground. (fig. 34.3)

Place (2140) Short Upright beside

(2137) SL Upright on the opposite side of

(2110) Slide Ground making sure that it

is plumb. Notice the angled edge slopes

away from (2110) Slide Ground. (fig. 34.2

and 34.3)

Loosely attach (2140) Short Upright and

(2137) SL Upright to (2110) Slide Ground

with 1 (H12) 1/4 x 3” Hex Bolt (with lock

washer, flat washer and t-nut) per board.

(fig. 34.3)

Refill hole halfway with soil and

compact making sure (2137) SL Upright

stays plumb. Finish filling and compacting.

(fig. 34.3)

Tighten bolts in (2140) Short Upright

and (2137) SL Upright then attach (2110)

Slide Ground to uprights with 1 (S3) #8 x

2-1/2” Wood Screw per board. (fig. 34.3)

WARNING:

Digging can be

dangerous if you do not check first for

underground wiring, cables or gas lines.

2137

6”

2140

2110

Angled edges slope

towards Side Ground

H12

1/4” lock

washer

1/4” flat

washer

1/4”

t-nut

1 x

Short Upright 2 x 3 x 33”

Hardware

Wood Parts

2 x

#8 x 2-1/2” Wood Screw

2 x

1/4 x 3” Hex Bolt

(1/4” lock washer, 1/4” flat washer, 1/4” t-nut)

H12

2140

S15

Summary of Contents for ASHBERRY II F23073C

















































































Search results

Summary of Contents for ASHBERRY II F23073C

Reviews:

Related manuals for ASHBERRY II F23073C

Brands by name

Popular brands

Big Backyard ASHBERRY II F23073C, Installation And Operating Instructions Manual

Search results

Summary of Contents for ASHBERRY II F23073C

Reviews:

Related manuals for ASHBERRY II F23073C

Brands by name

Popular brands