Big Backyard ASHBERRY II F23073C Installation And Operating Instructions Manual Download Page 47

Page: 47 / 80

[email protected]

Hardware

Wood Parts

1 x

Right Roof Board 1 x 4 x 30”

1 x

Left Roof Board 1 x 4 x 30”

2 x

Roof Support 2 x 2 x 29-1/4”

2109

6 x

#8 x 1-1/2” Wood Screw

4 x

#12 x 2” Pan Screw

Place 2 (2152) Roof Supports on the (2128) Siding so the ends are tight against the inside edges of (2118)

Front Trim and to the top of (2124) Front Floor, as shown in fig. 16.4 and 16.5. The top of the (2152) Roof Sup-

ports should form a peak and sit tight together. Attach to (2153) Posts and (2154) Front Posts with 2 (S7) #12 x 2”

Pan Screws in each support. (fig. 16.4, 16.5 and 16.6)

Place (2108) Left Roof Board and (2109) Right Roof Board on top of (2152) Roof Supports so they meet tight

in the centre and form a peak. Attach to each (2152) Roof Support with 3 (S2) #8 x 1-1/2” Wood Screws per

board, as shown in fig. 16.4, 16.5 and 16.6.

Step 16: Upper Front Wall Assembly

Part 3

Fig. 16.5

2128

Fig. 16.6

Fig. 16.4

2118

Tight

2152

2108

x 6

x 4

Roof boards flush in centre.

Roof supports flush in centre.

2152

2153

2154

2109

2128

2118

2152

2108

2124

Front Wall

Summary of Contents for ASHBERRY II F23073C

















































































Search results

Summary of Contents for ASHBERRY II F23073C

Reviews:

Related manuals for ASHBERRY II F23073C

Brands by name

Popular brands

Big Backyard ASHBERRY II F23073C, Installation And Operating Instructions Manual

Search results

Summary of Contents for ASHBERRY II F23073C

Reviews:

Related manuals for ASHBERRY II F23073C

Brands by name

Popular brands