Big Backyard ASHBERRY II F23073C Installation And Operating Instructions Manual Download Page 26

Page: 26 / 80

[email protected]

Step 5: Attach Swing End to Swing Beam

WARNING:

Glider Hangers must be tight

and secure to Swing Beams.

Place (4919) SW Rail Block in the centre between (1826) Front Beam and (1825) Back Beam and attach with

1 (H8) 1/4 x 4-1/4” Hex Bolt (with lock washer, flat washer and t-nut). (fig. 5.1 & 5.2)

Attach Big Backyard Plaque, with included hardware, over 1/4” t-nut on (1826) Front Beam. (fig. 5.1 & 5.2)

Attach Swing End Assembly to the side of the Swing Beam Assembly with the overhang (fig. 5.3 & 5.4) using

1 (G5) 5/16 x 4-1/2” Hex Bolt (with lock washer, flat washer and t-nut) in the top hole of Triangle Plate and 1 (G8)

5/16 x 2” Hex Bolt (with 2 flat washers and lock nut) in the bottom hole of Triangle Plate. (fig. 5.3) Make sure

Swing End Assembly flares out at an angle. (fig. 5.4)

Attach 2 Glider Hangers to the Swing Beam Assembly using 2 (G7) 5/16 x 5-1/2” Hex Bolt (with 2 flat washers

& lock nut) per Glider Hanger. (fig. 5.1 & 5.3)

Wood Parts

Other Parts

1 x

SW Rail Block 2 x 4 x 5-3/8”

4919

2 x Glider Hangers
1 x Big Backyard Plaque

(with hardware)

Hardware

1 x

1/4 x 4-1/4” Hex Bolt (1/4” lock washer, 1/4” flat washer, 1/4” t-nut)

1 x

5/16 x 4-1/2” Hex Bolt (5/16” lock washer, 5/16” flat washer, 5/16” t-nut)

4 x

5/16 x 5-1/2” Hex Bolt (5/16” flat washer x2, 5/16” lock nut)

1 x

5/16 x 2” Hex Bolt (5/16” flat washer x2, 5/16” lock nut)

H8
G5

100°

WARNING:

Glider Hangers must be tight

and secure to Swing Beams.

Glider

Hangers

Glider

Hanger

Side with

overhang

Fig. 5.1

Fig. 5.2

Fig. 5.3

Fig. 5.4

1/4” Flat

Washer

1/4” Lock

Washer

1/4”

T-Nut

5/16” Flat

Washer

5/16”

Lock Nut

5/16” Flat

Washer

5/16” Lock

Washer

5/16”

T-Nut

5/16” Flat

Washer

5/16”

Lock Nut

1825

Big Backyard Plaque

(with included hardware)

4919

1826

Summary of Contents for ASHBERRY II F23073C

















































































Search results

Summary of Contents for ASHBERRY II F23073C

Reviews:

Related manuals for ASHBERRY II F23073C

Brands by name

Popular brands

Big Backyard ASHBERRY II F23073C, Installation And Operating Instructions Manual

Search results

Summary of Contents for ASHBERRY II F23073C

Reviews:

Related manuals for ASHBERRY II F23073C

Brands by name

Popular brands