Big Backyard ASHBERRY II F23073C Installation And Operating Instructions Manual Download Page 6

Page: 6 / 80

Keys to Assembly Success

Part Identification Key

On each page, you will find the parts and

quantities required to complete the assembly

step illustrated on that page. Here is a sample.

Symbols

Throughout these instructions symbols are provided as important reminders for proper and safe assembly.

Proper Hardware Assembly

Lag screws require drilling pilot

holes to avoid splitting wood. Only

a flat washer is required. For ease of

installation liquid soap can be used

on all lag-type screws.

For bolts, tap T-Nut into hole with

hammer. Insert the hex bolt through

lock washer first then flat washer then

hole. Because the assemblies need to

be squared do not completely tighten

until instructed. Pay close attention to

diameter of the bolts. 5/16” is slightly

larger than 1/4”.

Once the assembly is tightened, watch for exposed

threads. If a thread protrudes from the T-Nut, remove the

bolt and add washers to eliminate this condition. Extra

washers have been provided for this purpose.

This identifies information that requires special

attention. Improper assembly could lead to an

unsafe or dangerous condition.

Where this is shown, 2 or 3

people are required to safely

complete the step. To avoid

injury or damage to the

assembly make sure to get help!

Check that assembly is square

before tightening bolts.

Use a measuring tape to assure

proper location.

Check that set or assembly is properly level

before proceeding.

Pre-drill a pilot hole before

fastening screw or lag to prevent

splitting of wood.

This indicates time to tighten bolts, but

not too tight! Do not crush the wood.

This may create splinters and cause

structural damage.

Use

Help

Use

Help

Measure

Distance

Square

Assembly

Use

Level

Pre-drill

1/8” Bit

Tighten

Bolts

Yes

CAUTION – Protrusion Hazard

Tools Required

Shovel

Level

#2 & #3 Phillips

or Robertson

Safety

Glasses

Drill (1/8”

3/16” Bit)

Measuring

Tape

Hammer

Ratchet 1/2”,

7/16” & 9/16”

Square

Ruler

Step

Ladder

1234

Post 2 x 4 x 83”

[email protected]

Summary of Contents for ASHBERRY II F23073C

















































































Search results

Summary of Contents for ASHBERRY II F23073C

Reviews:

Related manuals for ASHBERRY II F23073C

Brands by name

Popular brands

Big Backyard ASHBERRY II F23073C, Installation And Operating Instructions Manual

Search results

Summary of Contents for ASHBERRY II F23073C

Reviews:

Related manuals for ASHBERRY II F23073C

Brands by name

Popular brands