Big Backyard ASHBERRY II F23073C Installation And Operating Instructions Manual Download Page 67

Page: 67 / 80

[email protected]

Glider Rope

and Chain

Glider End

5/16 Flat

Washers

Glider Seat

5/16 x 6” Hex

Bolt

5/16 Flat

Washer-Zinc

5/16 Lock

Nuts

5/16 Flat

Washer-Zinc

5/16 Lock

Nuts

WARNING:

Bolt must not

exceed 1/2 thread past the nut

5/16 Lock

Nuts

2 x Glider Ends
1 x Glider Seat
1 x Glider Rope and Chain (pkg of 4)

2 x

5/16 x 6” Hex Bolt

(5/16” flat washer x 2, 5/16” lock nut)

8 x 5/16” Flat Washer
4 x 5/16” Lock Nut

Hardware

Other Parts

Fig. 30.1

Step 30: Glider Assembly

Attach 1 Glider End to the Glider Seat using 1 (Z) 5/16 x 6” Hex Bolt (with 2 flat washers and 1 lock nut).

Repeat for the second Glider End. (fig. 30.1)

Install 2 Glider Rope with Chains into each Glider End using 2 - 5/16” Flat Washers and 1 Lock Nut per rope.

(fig. 30.1)

Summary of Contents for ASHBERRY II F23073C

















































































Search results

Summary of Contents for ASHBERRY II F23073C

Reviews:

Related manuals for ASHBERRY II F23073C

Brands by name

Popular brands

Big Backyard ASHBERRY II F23073C, Installation And Operating Instructions Manual

Search results

Summary of Contents for ASHBERRY II F23073C

Reviews:

Related manuals for ASHBERRY II F23073C

Brands by name

Popular brands