Big Backyard ASHBERRY II F23073C Installation And Operating Instructions Manual Download Page 35

Page: 35 / 80

[email protected]

2 x

#8 x 1-3/4” Wood Screw

2 x

#12 x 2” Pan Screw

(with 3/16” flat washer)

2 x

#8 x 3” Wood Screw

Hardware

Wood Parts

4 x

1/4 x 2” Hex Bolt

(1/4” lock washer, 1/4” flat washer, 1/4” t-nut)

1 x

1/4 x 4” Hex Bolt

(1/4” lock washer, 1/4” flat washer, 1/4” t-nut)

1 x

1/4 x 4-1/2” Hex Bolt

(1/4” lock washer, 1/4” flat washer, 1/4” t-nut)

1 x

Middle Front 1 x 5 x 65-5/8”

1 x

SL Post 2 x 4 x 32-1/2”

2125

2112

Step 9: Front Wall Assembly

Part 4

Loosely attach (2125) Middle Front on the outside of the assembly to both (2153) Posts and both (2154) Front

Posts with 4 (H2) 1/4 x 2” Hex Bolts (with lock washer, flat washer and t-nut). (fig. 9.4)

Make sure the distance between (2114) Top Front and (2125) Middle Front is 9-1/2” then attach (2125)

Middle Front to each (2153) Post with 2 (S15) #8 x 1-3/4” Wood Screws. Tighten the bolts from Step F. (fig. 9.4

and 9.5)

At the ends of (2125) Middle Front and (2120) Floor Front Back place (2112) SL Post as shown in fig. 9.4.

Attach (2112) SL Post to (2124) Front Floor with 1 (H5) 1/4 x 4-1/2” Hex Bolt (with lock washer, flat washer and

t-nut) in the bottom hole and 1 (S7) #12 x 2” Pan Screw (with flat washer) in the top hole and to (2125) Middle

Front with 1 (H4) 1/4 x 4” Hex Bolt (with lock washer, flat washer and t-nut) in the top hole and 1 (S7) #12 x 2”

Pan Screw (with flat washer) in the bottom hole. (fig. 9.4)

Attach (2112) SL Post to (2120) Floor Front Back with 2 (S4) #8 x 3” Wood Screws. (fig. 9.4)

Outside View

1/4” lock

washer

1/4” flat

washer

1/4” t-nut

S15

Fig. 9.4

2125

S15

2153

2112

2124

2154

2153

with 3/16”

flat washer

2120

Fig. 9.5

S15

2153

2125

2114

1/4” t-nut

1/4” flat

washer

1/4” lock

washer

9-1/2”

Summary of Contents for ASHBERRY II F23073C

















































































Search results

Summary of Contents for ASHBERRY II F23073C

Reviews:

Related manuals for ASHBERRY II F23073C

Brands by name

Popular brands

Big Backyard ASHBERRY II F23073C, Installation And Operating Instructions Manual

Search results

Summary of Contents for ASHBERRY II F23073C

Reviews:

Related manuals for ASHBERRY II F23073C

Brands by name

Popular brands