Big Backyard ASHBERRY II F23073C Installation And Operating Instructions Manual Download Page 40

Page: 40 / 80

[email protected]

Step 12: Slide Wall Assembly

1 x

Lower Bench 1 x 4 x 38-7/8”

1 x

SL Floor End 2 x 4 x 38-7/8”

1 x

Lower Floor Support 5/4 x 4 x 38-7/8”

1 x

Side Ground 1 x 5 x 38-3/4”

2144

2122

Loosely attach (2127) Side Ground to the outside of each (2153) Post on the Slide Wall side with 4 (H4) 1/4 x

4” Hex Bolts (with lock washer, flat washer and t-nut). (fig. 12.1)

Attach (2122) SL Floor End flush to the bottom of each (2112) SL Post with 8 (S3) #8 x 2-1/2” Wood Screws.

(fig. 12.1)

Tight to the bottom of (2123) Back Floor and (2124) Front Floor and flush to the outside edges of (2153)

Posts attach (2103) Lower Floor Support with 4 (S7) #12 x 2” Pan Screws. (fig. 12.1)

Attach 1 (2144) Lower Bench flush to the tops of each (2112) SL Post with 4 (S2) #8 x 1-1/2” Wood Screws.

(fig. 12.1)

Hardware

Wood Parts

1/4”

t-nut

Fig. 12.1

2144

Slide Wall

Back

1/4” lock

washer

1/4” flat

washer

x 4

4 x

1/4 x 4” Hex Bolt

(1/4” lock washer, 1/4” flat washer, 1/4” t-nut)

4 x

#8 x 1-1/2” Wood Screw

4 x

#12 x 2” Pan Screw

x 4 per side

x 4

2122

2103

flush

2112

2124

Front

2153

8 x

#8 x 2-1/2” Wood Screw

2103

2127

2123

Summary of Contents for ASHBERRY II F23073C

















































































Search results

Summary of Contents for ASHBERRY II F23073C

Reviews:

Related manuals for ASHBERRY II F23073C

Brands by name

Popular brands

Big Backyard ASHBERRY II F23073C, Installation And Operating Instructions Manual

Search results

Summary of Contents for ASHBERRY II F23073C

Reviews:

Related manuals for ASHBERRY II F23073C

Brands by name

Popular brands