Big Backyard ASHBERRY II F23073C Installation And Operating Instructions Manual Download Page 55

Page: 55 / 80

[email protected]

Step 20: Lower Slide Wall Assembly

Part 2

Tight to the bottom of (2129) Cafe Support and flush to outside edges of both (2153) Posts attach (2155)

Siding Narrow to each post with 2 (S0) #8 x 7/8” Truss Screws as shown in fig. 20.4 and 20.6.

Tight to bottom of (2155) Siding Narrow and flush to the outside edges of both (2153) Posts attach 4

(2116) Siding to each post with 2 (S0) #8 x 7/8” Truss Screws per board, as shown in fig. 20.4 and 20.6.

Make sure there are no gaps between boards. The bottom (2116) Siding will be tight to the top of (2127) Side

Ground.

From inside the assembly place (2135) Wall Support over the centre pilot holes of the (2116) Siding and

(2155) Siding Narrow and tight to the top of Cafe Assembly then attach from outside of the assembly with 1

(S0) #8 x 7/8” Truss Screw per siding and 2 (S15) #8 x 1-3/4” Wood Screws in (2127) Side Ground. (fig. 20.5

and 20.6)

Hardware

Wood Parts

15 x

#8 x 7/8” Truss Screw

2 x

#8 x 1-3/4” Wood Screw

1 x

Siding Narrow 3/8 x 3 x 38-3/4”

4 x

Siding 3/8 x 3-1/2 x 38-3/4”

1 x

Wall Support 2 x 2 x 22-1/4”

2155

2116

Fig. 20.5

2153

x 3 per board

Fig. 20.4

Fig. 20.6

Inside View

Slide Wall

Outside View

2153

2127

2155

2116

2135

Slide Wall

2135

Cafe Assembly

S15

2129

Summary of Contents for ASHBERRY II F23073C

















































































Search results

Summary of Contents for ASHBERRY II F23073C

Reviews:

Related manuals for ASHBERRY II F23073C

Brands by name

Popular brands

Big Backyard ASHBERRY II F23073C, Installation And Operating Instructions Manual

Search results

Summary of Contents for ASHBERRY II F23073C

Reviews:

Related manuals for ASHBERRY II F23073C

Brands by name

Popular brands