Big Backyard ASHBERRY II F23073C Installation And Operating Instructions Manual Download Page 42

Page: 42 / 80

[email protected]

Wood Parts

Hardware

70 x

#8 x 1-1/2” Wood Screw

1 x

CE Gap Board 1 x 4 x 38-3/4”

2 x

End Board 1 x 6 x 38-3/4”

8 x

Cedar Floor Board 1 x 5 x 38-3/4”

1 x

Cedar Gap Board 1 x 5 x 38-3/4”

2 x

Middle Gap Board 1 x 5 x 38-3/4”

2136

Step 13: Floor Assembly

Part 2

Place 1 (2147) End Board at Swing Wall side tight to (2126) SW Floor and (2134) Cedar Gap Board on Slide

Wall side tight to (2122) SL Floor End.

: Starting on the Swing Wall side place 3 (2158) Cedar Floor Boards followed by 1 (2104) Middle Gap Board

so the gap in the board fits around the (2154) Front Post, then the (2136) CE Gap Board, another (2104) Middle

Gap Board, 3 more (2158) Cedar Floor Boards, 1 (2147) End Board and then the last 2 (2158) Cedar Floor

Boards . Make sure all boards are evenly spaced. (fig. 13.2)

Attach all boards to both (2120) Floor Front Backs and (2142) Floor Joist with 5 (S2) #8 x 1-1/2” Wood

Screws per board. (fig. 13.2)

Fig. 13.2

2153

Swing Wall

x 5 per

board

Slide Wall

2120

(hidden)

Back Wall

Front Wall

2122

2136

2147

2120

(hidden)

2134

2158

2142

(hidden)

2104

2124

2104

2134

2158

2147

2123

2126

2147

2154

2158

Summary of Contents for ASHBERRY II F23073C

















































































Search results

Summary of Contents for ASHBERRY II F23073C

Reviews:

Related manuals for ASHBERRY II F23073C

Brands by name

Popular brands

Big Backyard ASHBERRY II F23073C, Installation And Operating Instructions Manual

Search results

Summary of Contents for ASHBERRY II F23073C

Reviews:

Related manuals for ASHBERRY II F23073C

Brands by name

Popular brands