Big Backyard ASHBERRY II F23073C Installation And Operating Instructions Manual Download Page 48

Page: 48 / 80

[email protected]

Hardware

Wood Parts

6 x

Trim 5/8 x 1-3/4 x 16-1/4”

2 x

Window Brace 1 x 2 x 9-1/2”

2 x

Oval Window 1 x 6 x 8-1/4”

1 x

Window Frame 1 x 2 x 16-1/4”

2133

20 x

#8 x 1-1/8” Wood Screw

On the inside of the assembly, flush to the top of (2114) Top Front and tight to the inside of each (2153) Post

and on each side of both (2154) Front Posts attach 6 (2133) Trim to (2114) Top Front and (2125) Middle Front with

2 (S1) #8 x 1-1/8” Wood Screws per trim. (fig. 16.7 and 16.8)

On the outside of the assembly tight to the top of (2125) Middle Front and flush to the outside edges of 2 centre

(2133) Trim, as shown in fig. 16.10, attach (0389) Window Frame to (2133) Trim with 2 (S1) #8 x 1-1/8” Wood

Screws. (fig. 16.9 and 16.10)

Tight to top of (0389) Window Frame and flush to the outside edges of 2 (2133) Trim attach 2 (2119) Oval

Windows from inside the assembly to each of the 4 centre (2133) Trims with 1 (S1) #8 x 1-1/8” Wood Screw per

trim. (fig. 16.10)

Attach 1 (1740) Window Brace flush to the inside edge of each outer (2133) Trim with 1 (S1) #8 x 1-1/8” Wood

Screw per trim. (fig. 16.10)

Step 16: Upper Front Wall Assembly

Part 4

Fig. 16.7

Tight

2153

Fig. 16.8

Fig. 16.9

Fig. 16.10

Flush

2114

2133

x 2 per

board

2154

Tight

2125

Tight

Inside View

2153

Front Wall

Outside View

2114

2153

2125

2133

2153

2133

0389

2119

x 8

0389

2119

1740

Summary of Contents for ASHBERRY II F23073C

















































































Search results

Summary of Contents for ASHBERRY II F23073C

Reviews:

Related manuals for ASHBERRY II F23073C

Brands by name

Popular brands

Big Backyard ASHBERRY II F23073C, Installation And Operating Instructions Manual

Search results

Summary of Contents for ASHBERRY II F23073C

Reviews:

Related manuals for ASHBERRY II F23073C

Brands by name

Popular brands