Barrett 2030 Operating And Installation Manual Download Page 2

Page: 2 / 208

BARRETT 2030 HF SSB TRANSCEIVER

2 of 208

Barrett 2030 Compliance .............................................................................................................. 6

FCC RF Exposure Compliance Statement .......................................................................... 6

FCC RF Exposure Warning .................................................................................................. 7

FCC Modulation Modes ........................................................................................................ 7

Industry Canada Modulation Modes .................................................................................... 7

About this Operating and Installation Manual ............................................................................ 8

Icons and Standards ............................................................................................................. 8

Scroll Keys .............................................................................................................. 8

Abbreviations and Acronyms .............................................................................................. 8

Introduction .................................................................................................................................. 10

Operation ...................................................................................................................................... 11

User Controls ....................................................................................................................... 11

2030 Transceiver Front Panel Description ............................................................ 11

Keypad .................................................................................................. 12

Locking and Unlocking the Keypad ....................................................... 14

2030 Transceiver Control Head Rear View ........................................................... 16

Microphone Socket ............................................................................... 16

Transceiver Socket ............................................................................... 16

2030 Transceiver Rear Panel Description ............................................................ 17

Switching on the Transceiver ............................................................................................ 18

Switching on the Transceiver – Without a PIN ...................................................... 18

Switching on the Transceiver – With a PIN ........................................................... 18

Switching Off the Transceiver ............................................................................... 18

Display .................................................................................................................................. 19

Receive Mode ....................................................................................................... 19

Transmit Mode ...................................................................................................... 19

Secure Mode ......................................................................................................... 20

Channel Attributes ................................................................................................. 20

Adjusting the Audio Volume .............................................................................................. 21

Selecting a Channel ............................................................................................................ 21

Using Channel Up/Down Keys .............................................................................. 21

Direct Channel Number Entry ............................................................................... 22

Using the Microphone ......................................................................................................... 23

Barrett Selective Calling System ....................................................................................... 24

General ................................................................................................................. 24

International .......................................................................................... 24

OEM 1 ................................................................................................... 24

CCIR ..................................................................................................... 24

Selective Call –“Selcall” ........................................................................ 25

Selective Call “Telcall” .......................................................................... 25

Special Notes When Using OEM 1 Selective Call Protocol .................. 25

More Selective Calling Information ................................................................................... 26

Selcall Self IDs ...................................................................................................... 26

Selcall Decode ...................................................................................................... 26

Selcall Transmit ..................................................................................................... 26

Default Self IDs ..................................................................................................... 27

Setting Default Self IDs ......................................................................... 27

Detaching an ID from the Default Self IDs ............................................ 28

Contacting Another Station - Using Selective Call “Selcall” and Telcall ................ 29

Entering Station IDs and Using the Address and Telephone Books ..................... 29

When Asked to Enter a Station ID:- ...................................................... 29

Summary of Contents for 2030

















































































































































































































Search results

Summary of Contents for 2030

Reviews:

Related manuals for 2030

Brands by name

Popular brands

Barrett 2030, Operating And Installation Manual

Search results

Summary of Contents for 2030

Reviews:

Related manuals for 2030

Brands by name

Popular brands