Barrett 2030 Operating And Installation Manual Download Page 26 | Manualshive

Page: 26 / 208

background image

BARRETT 2030 HF SSB TRANSCEIVER

26 of 208

More Selective Calling Information

Selcall Self IDs

As from software version 2.00 the 2030 transceiver can have up to 10 Selcall self
IDs assigned to it. These Selcall IDs can be any combination of 4 or 6 digit OEM or
International type id.

Selcall Decode

As from software version 2.00 the 2030 transceiver has the ability to decode both
OEM and International Selcalls on any channel programmed as a Selcall channel.
Calls for each format type will only be decoded if there is at least one self id of that
format programmed into the transceiver self id group.

Selcall Transmit

Selcall formats in transmit are channel specific, only call types programmed for the
channel are permitted. This means International and CCIR format calls can only be
sent on channels that are programmed as International or CCIR Selcall channels,
OEM calls can only be sent on channels that are programmed as OEM Selcall
channels.

«
...
24
25
26
27
28
...
»

Summary of Contents for 2030

















































































































































































































Reviews:

No comments

Related manuals for 2030

Brand: Panasonic Pages: 2

Brand: E+E Elektronik Pages: 2

Brand: Magnetek Pages: 2

Brand: Parkside Pages: 65

Brand: Sangean Pages: 1

Brand: Sandstrom Pages: 4

Brand: Elma Instruments Pages: 8

Brand: Pro Electronic Pages: 32

Brand: FTE Maximal Pages: 44

Brand: Vaisala Pages: 50

Brand: Trantec Pages: 22

Brand: Yaesu Pages: 88

Brand: Mpow Pages: 12

Diversity Nano RX

Brand: TBS CROSSFIRE Pages: 3

Brand: Aiwa Pages: 18

Brand: M-system Pages: 7

Brand: Icom Pages: 3

Brand: Effort International Pages: 23

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands