Barrett 2030 Operating And Installation Manual Download Page 106 | Manualshive

Page: 106 / 208

background image

BARRETT 2030 HF SSB TRANSCEIVER

Option Installation

Options are installed in the Barrett 2030 transceiver by entering a PIN number
supplied by the manufacturer. This PIN number is related to the electronic serial
number of the transceiver. A different PIN number is provided depending on the
option or combination of options required to be fitted. Most options are fitted in the
factory before dispatch.

press the

key

enter the option PIN number supplied by the manufacturer using

the numeric keypad then press the

key

For example if the PIN number supplied is for all available 2030

options, after entering the PIN number the following is displayed:-

If an incorrect PIN number is entered the following is displayed:-

106 of 208

«
...
104
105
106
107
108
...
»

Summary of Contents for 2030

















































































































































































































Reviews:

No comments

Related manuals for 2030

Brand: iDirect Pages: 82

Brand: Daspi Pages: 2

Brand: M-system Pages: 4

Brand: Uniden Pages: 17

Brand: X10 Pages: 7

IMPERIAL HD 2 basic

Brand: DigitalBox Pages: 96

Brand: Cooper Pages: 120

Brand: Erreka Pages: 4

Brand: Onkyo Pages: 81

Brand: Garmin Pages: 41

Wireless A/V Sender 2.4GHz

Brand: Quatech Pages: 8

Brand: BNF Pages: 45

Brand: HOLATRON SYSTEMS Pages: 12

Brand: Kramer Pages: 12

Brand: YOKOGAWA Pages: 72

Brand: cctv camera pros Pages: 9

CamLock UPM PM1RM

Brand: B-K lighting Pages: 9

Brand: SIIG Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands