Barrett 2030 Operating And Installation Manual Download Page 141 | Manualshive

Page: 141 / 208

background image

BARRETT 2030 HF SSB TRANSCEIVER

RF Settings

Optional IF Filter Enable

When enabled the optional IF filter (if physically fitted) is selected automatically
when AFSK or CW mode is selected. This is useful when the transceiver is used in
some data transmission applications. Two options are available, “Narrow” or
“Wide”. When “Narrow” is selected the filter bandwidth is 500Hz. If “Wide” is
selected then the filter bandwidth is 3 kHz.

Use

the

Scroll keys

to select the setting required (example

shown

“Wide”):-

press

the

key

Note:-

This setting is only available if the narrow filter setting is enabled via the

2000 series programming software.

141 of 208

«
...
139
140
141
142
143
...
»

Summary of Contents for 2030

















































































































































































































Reviews:

No comments

Related manuals for 2030

Brand: Harman Kardon Pages: 3

Brand: Kathrein Pages: 44

Brand: Nautel Pages: 229

Brand: Nautel Pages: 18

Brand: Nautel Pages: 326

Discovery Series

Brand: Hall Technologies Pages: 13

Brand: SpeakerCraft Pages: 8

Brand: Stabila Pages: 10

Brand: Omicron Pages: 25

Campersat Autoseek Autoskew System 4441

Brand: Campersat Pages: 14

Brand: Aiwa Pages: 37

Brand: B&K Pages: 12

Brand: T+A Elektroakustik Pages: 60

Brand: Cabletron Systems Pages: 41

Brand: Jensen Pages: 28

Brand: Topp Music Gear Pages: 4

Brand: PR electronics Pages: 28

PEP2000 - UPDATE V0150 AND V11.53

Brand: Yaesu Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands