Barrett 2030 Operating And Installation Manual Download Page 17

Page: 17 / 208

BARRETT 2030 HF SSB TRANSCEIVER

2030 Transceiver Rear Panel Description

Input for GPS receiver Barrett P/N BCA20009 for vehicle tracking/location
applications.

Output for cooling fan unit Barrett P/N BCA20002 for high duty cycle
applications.

Interface for Barrett automatic tuning mobile antenna and marine automatic
antenna tuners.

Power input and speaker output for use with 2022 power supply.

Auxiliary antenna socket (channels can be programmed to use this socket or
the main antenna socket when using different antennas).

Main antenna socket.

Auxiliary interface connector.

Input for CW key Barrett P/N BCA20014.

Output for loudspeaker Barrett P/N BCA20015.

Chassis earth connection.

17 of 208

Summary of Contents for 2030

















































































































































































































Search results

Summary of Contents for 2030

Reviews:

Related manuals for 2030

Brands by name

Popular brands

Barrett 2030, Operating And Installation Manual

Search results

Summary of Contents for 2030

Reviews:

Related manuals for 2030

Brands by name

Popular brands