Barrett 2030 Operating And Installation Manual Download Page 161 | Manualshive

Page: 161 / 208

background image

BARRETT 2030 HF SSB TRANSCEIVER

Gently lever the two plastic covers off to provide access to the connectors.
Remove the short interface cable from the remote head and transceiver body and
replace with the long interface cable. Insert the speaker cable into the correct
socket on the remote head.

Replace the cover on the transceiver body taking care to place the cable grommet
around the interface cable. If required, this cover, whilst having clips, can then be
secured with M3 screws to provide a solid cable clamp.

161 of 208

«
...
159
160
161
162
163
...
»

Summary of Contents for 2030

















































































































































































































Reviews:

No comments

Related manuals for 2030

DuoPak APD 2015

Brand: Absolute Process Instruments Pages: 2

Brand: Harris Pages: 148

Brand: Harman Kardon Pages: 4

Brand: Harris Pages: 4

Brand: Laird Pages: 13

Brand: Laird Pages: 32

Brand: Vector Pages: 5

Brand: Nautel Pages: 83

Brand: Tiviar Pages: 72

Brand: WAC Lighting Pages: 6

Brand: a-them Pages: 66

Brand: AAS Pages: 4

Brand: Xoro Pages: 78

BTL7-V50E-M P-C003 Series

Brand: Balluff Pages: 100

Brand: Intermatic Pages: 2

Brand: Inovonics Pages: 2

Brand: Hallicrafters Pages: 8

Brand: Vaisala Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands