Barrett 2030 Operating And Installation Manual Download Page 7 | Manualshive

Page: 7 / 208

background image

BARRETT 2030 HF SSB TRANSCEIVER

FCC RF Exposure Warning

To ensure optimal transceiver performance and to avoid exposure to excessive
electromagnetic fields, the antenna system must be installed according to the
instructions provided.

High voltages exist on the antenna during transmission and tuning. Do not touch
the antenna during these activities. RF burns may result.

Install the grounding system or counterpoise as directed to prevent RF burns from
any metal part of the transceiver.

Safe working distance is based on continuous exposure to CW type transmissions,
as set out in the ICNIRP Exposure Guidelines (1998) for occupational exposure.
Safe working distance can be reduced with normal voice communication.

For FCC compliance, when the 2030 transceiver is used at a power level of

100 watts PEP, the antenna(s) used with this transceiver should be located at least
3 metres from the operator and should not be co-located or operating in conjunction
with any other antenna or transmitter.

FCC Modulation Modes

Please note that J3E Upper Sideband Mode is the only modulation mode available
for operation in the United States of America.

Industry Canada Modulation Modes

Please note that J3E Upper Sideband Mode is the only modulation mode available
for operation in Canada.

7 of 208

«
...
5
6
7
8
9
...
»

Summary of Contents for 2030

















































































































































































































Reviews:

No comments

Related manuals for 2030

Brand: Varec Pages: 38

Masoneilan 8000

Brand: Baker Hughes Pages: 24

Sat-Light 7410F

Brand: Foxcom Pages: 74

BTL6-A 5 00-M0500-PF-S115

Brand: Balluff Pages: 22

Brand: Transition Networks Pages: 1

Brand: Trust Pages: 9

Brand: IBR Pages: 20

Brand: M-system Pages: 5

Brand: BluStream Pages: 4

Brand: Future light Pages: 31

Brand: M-system Pages: 2

Brand: A-Neuvideo Pages: 11

Brand: Trillium Pages: 2

Brand: Cabletron Systems Pages: 41

Brand: FAAC Pages: 4

Brand: Spektrum Pages: 16

Brand: Samson Pages: 24

Brand: ZGEMMA Pages: 31

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands