Barrett 2030 Operating And Installation Manual Download Page 40

Page: 40 / 208

BARRETT 2030 HF SSB TRANSCEIVER

Emergency Calls

All Selcall emergency calls are transmitted by pressing the

button for

more than two seconds and less than ten seconds and releasing, the alarm
sequence starts upon button release.

The action of the emergency call button depends on transceiver programming:-

Selective Call alarm that only transmits on the currently selected channel.

Transmits the emergency Selcall sequence once on each press of the

button.

If a GPS receiver is fitted and enabled the GPS position is also sent in the call.

Selective Call alarm that transmits and automatically changes to a selection
of channels.

Transmits the emergency Selcall sequence twice on each channel programmed as
an emergency channel, repeating this sequence until the transceiver is switched off

If a GPS receiver is fitted and enabled the GPS position is also sent in the call.

Note:-

In all of the alarms above, after the alarm has been activated by using the

button, there is no indication that an alarm is being sent for security

purposes.

40 of 208

Summary of Contents for 2030

















































































































































































































Search results

Summary of Contents for 2030

Reviews:

Related manuals for 2030

Brands by name

Popular brands

Barrett 2030, Operating And Installation Manual

Search results

Summary of Contents for 2030

Reviews:

Related manuals for 2030

Brands by name

Popular brands