Barrett 2030 Operating And Installation Manual Download Page 118

Page: 118 / 208

BARRETT 2030 HF SSB TRANSCEIVER

Scan Table Select

This section selects the Scan table to be used when the transceiver is put in scan,
or if enabled, when scan resume occurs.
There are 8 scan tables.

Note:-

When scrolling through the scan tables, before selection, only those with

channels entered will be displayed.

Note:-

Channels can be added, removed and edited and scan tables named in the

“

Scan table

” section.

Use

the

Scroll keys

to select the scan table required (example

scan table 1):-

When the scan table required is displayed press the

key

If none of the Scan tables have any channel entries the

following is displayed:-

Note:-

Direct entry into this section is available by pressing the

key for

more than two seconds

118 of 208

Summary of Contents for 2030

















































































































































































































Search results

Summary of Contents for 2030

Reviews:

Related manuals for 2030

Brands by name

Popular brands

Barrett 2030, Operating And Installation Manual

Search results

Summary of Contents for 2030

Reviews:

Related manuals for 2030

Brands by name

Popular brands