Barrett 2030 Operating And Installation Manual Download Page 185 | Manualshive

Page: 185 / 208

background image

BARRETT 2030 HF SSB TRANSCEIVER

185 of 208

Barrett 2019 Automatic Tuning Mobile HF Antenna

- Barrett P/N 2019-00-10

The Barrett 2019 automatic tuning mobile HF antenna plugs directly into the rear of
a 2030 transceiver using the cables supplied.

Important:-

2030 transceivers must

have either the 2019 or 910 antenna option set during programming.

Mounting the Barrett 2019 Automatic Tuning Mobile HF Antenna

The Barrett 2019 antenna should be mounted in positions similar to those illustrated
in the diagrams on the following pages. Select a position free from excessive
vibration. A bracket, fabricated to withstand the forces and vibration that can be
expected during off-road driving, should be used to mount the antenna to the
vehicle. When locating the mounting position for the antenna ensure that the
antenna body, when flexing on its vibration mount, cannot come into contact with
other parts of the vehicle. The antenna should be mounted as far from surrounding
objects on the vehicle as possible.

The antenna is supplied with one middle section and one top whip section (Barrett
P/N: BCA201901), a tapered black spring (Barrett P/N: BCA201903), an antenna
installation guide and a pre-terminated 6 metre control cable to suit the Barrett 2019
antenna to transceiver. A 6 metre (Barrett P/N: BCA201904) or 10 metre (Barrett
P/N: BCA201902) extension cable for the control cable is also available.

The control cable should be routed into either the engine compartment or boot
(trunk) of the vehicle. If the joint between the antenna control cable and the
extension cable is in an exposed position, a butyl rubber self amalgamating tape
should be used to seal the joint. Do not wrap this joint if it cannot be made
completely water tight as water will collect in the joint and cause it to corrode.

A good earth (ground) to the main body of the vehicle is essential for efficient
operation of the antenna.

To achieve this clean all joints to bare metal and use

copper braid earth straps if any non-metallic joints are encountered.

After mounting the main body of the antenna, screw the black base spring onto the
antenna body followed by the whip section.

Important Information

It is ESSENTIAL to maintain the minimum clearances between the antenna
and surrounding metal work as indicated in the diagrams. FAILURE TO
MAINTAIN THESE CLEARANCES WILL NOT ONLY REDUCE THE EFFICIENCY
OF THE BARRETT 2019 AUTOMATIC TUNING MOBILE HF ANTENNA BUT
MAY ALSO LEAD TO INTERNAL RF ARCING AND FAILURE.

«
...
183
184
185
186
187
...
»

Summary of Contents for 2030

















































































































































































































Reviews:

No comments

Related manuals for 2030

Brand: Arteche Pages: 9

Brand: XIEGU Pages: 48

Brand: XIEGU Pages: 13

Brand: Varec Pages: 24

Brand: Magnetrol Pages: 16

Brand: Magnetrol Pages: 108

Brand: Magnetrol Pages: 35

Brand: Magnetek Pages: 25

Brand: Yamaha Pages: 75

Brand: Akai Pages: 33

Brand: Alinco Pages: 16

Brand: Alinco Pages: 71

GE-PON OLT Transceiver OPEP-33-B4K3R

Brand: Delta Pages: 8

Brand: XRadio Pages: 29

Brand: Smarthome Pages: 2

Brand: Orava Pages: 10

Brand: Topfield Pages: 58

Brand: Fusion Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands