Barrett 2030 Operating And Installation Manual Download Page 79 | Manualshive

Page: 79 / 208

background image

BARRETT 2030 HF SSB TRANSCEIVER

Call History

Whenever a Selcall, Telcall, Allcall, Group call, Sub-group call, Pagecall, Statcall
GPS or Emergency call is received or transmitted its details are held in a first in first
out call history buffer.

Received calls that have not been viewed before are held in a section called “New
Calls”, received calls that have been viewed are held for future viewing in the
“Inbox” all transmitted calls are stored in the “Outbox”. Each history buffer can store
up to 30 entries.

New Call

This section lists all types of Selcalls that have been received but not yet viewed:-

Inbox

This section lists all types of Selcalls that have been received and viewed and
stored for future reference:-

79 of 208

«
...
77
78
79
80
81
...
»

Summary of Contents for 2030

















































































































































































































Reviews:

No comments

Related manuals for 2030

Brand: VIETA Pages: 66

Brand: RKI Instruments Pages: 65

Brand: Tevion Pages: 22

Brand: Leica Pages: 32

Brand: LD Pages: 4

Brand: Ocean Signal Pages: 28

Brand: Vaisala Pages: 70

Brand: Navilock Pages: 11

Brand: Voscom Pages: 18

TeCom-DualBand PR5058

Brand: Team Electronic Pages: 33

Portable Transducer

Brand: Humminbird Pages: 2

Brand: Vivax Metrotech Pages: 4

Brand: Q5X Pages: 12

Brand: Camille Bauer Pages: 2

Brand: Lectrosonics Pages: 8

Phase Linear UV7

Brand: Audiovox Pages: 6

Brand: M-system Pages: 3

WMS Hand-held transmitter comfort

Brand: WAREMA Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands