Barrett 2030 Operating And Installation Manual Download Page 148 | Manualshive

Page: 148 / 208

background image

BARRETT 2030 HF SSB TRANSCEIVER

Antenna Type

This section sets antenna type or if a linear amplifier is to be used with the 2030
transceiver.

Selections available:-

“Base Station”

Select when base station antennas such as the Barrett 2012 series are used. No
tuning signals are emitted on channel change. This selection should also be used
when operating with a Barrett 2014 manual tapped whip.

“910 Mobile Antenna”

Select when using a Barrett 910 automatic tuning mobile antenna.

“911 Automatic Tuner”

Select when using a Barrett 911 automatic tuner.

“Linear Amplifier”

Select when using the 2030 with a Barrett 2075 series linear amplifier.

“2019 Mobile Antenna”

Select when using a Barrett 2019 automatic tuning mobile HF antenna.

“Loop Antenna”

Select when using the 2018 Mobile magnetic loop HF antenna.

“Linear with ATU”

Select when using the 2030 with a Barrett 2075 series linear amplifier fitted with an
automatic tuning unit.

148 of 208

«
...
146
147
148
149
150
...
»

Summary of Contents for 2030

















































































































































































































Reviews:

No comments

Related manuals for 2030

Brand: Hallicrafters Pages: 8

Brand: Ham Pages: 37

L-1DVI-FE-TX/RX

Brand: Questtel Pages: 4

Brand: Berker Pages: 6

Brand: Jung Pages: 5

STORM PRO C-4014

Brand: Feniex Pages: 13

Brand: sunair Pages: 188

Brand: Ham radio Pages: 14

Brand: M-system Pages: 2

Brand: Vaisala Pages: 18

ASGARD CCT Series

Brand: Fema Electronica Pages: 4

Brand: LVSUN Pages: 7

Brand: PR electronics Pages: 28

Brand: AOR Pages: 4

Brand: Intel Pages: 80

Brand: Topfield Pages: 72

Brand: YOKOGAWA Pages: 2

Brand: Jamara Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands