Barrett 2030 Operating And Installation Manual Download Page 181

Page: 181 / 208

BARRETT 2030 HF SSB TRANSCEIVER

Connection details - 2030 Transceiver with Mobile Pack and 2019 Automatic
Tuning Mobile HF Antenna

Barrett 2019 Automatic Tuning Mobile HF Antenna

2030 control head

Cable with RJ45 connectors (P/N BCA29995)

Microphone

Heavy duty fuse & holder (P/N BCA20021) supplied in mobile
pack.

6 metre power cable supplied with transceiver

2030 transceiver body

Extension speaker supplied with 2030 transceiver

Connection for external fan unit

Interface cable – integral coaxial, control and optional GPS
connection

Auxiliary connector

External GPS – (used if optional internal 2019 GPS unit is not
required or fitted)

Earth cable

181 of 208

Summary of Contents for 2030

















































































































































































































Search results

Summary of Contents for 2030

Reviews:

Related manuals for 2030

Brands by name

Popular brands

Barrett 2030, Operating And Installation Manual

Search results

Summary of Contents for 2030

Reviews:

Related manuals for 2030

Brands by name

Popular brands