Barrett 2030 Operating And Installation Manual Download Page 27 | Manualshive

Page: 27 / 208

background image

BARRETT 2030 HF SSB TRANSCEIVER

Default Self IDs

Default self IDs are the IDs used when making a selective call. They are used when
the self ID is not set during the call procedure or the Selcall address book entry
being used does not have a self ID attached to it.

Setting Default Self IDs

then press the

key

Use the scroll keys to select the self id to attach to the default ID
(in this case the 4 digit OEM default ID)

then press the

key

Repeat the steps above for each default ID

27 of 208

«
...
25
26
27
28
29
...
»

Summary of Contents for 2030

















































































































































































































Reviews:

No comments

Related manuals for 2030

Brand: JBL Pages: 105

Brand: Alinco Pages: 48

Brand: Paul Wegener Pages: 8

Brand: C & K Systems Pages: 2

Brand: Kramer Pages: 35

Brand: Onkyo Pages: 285

Brand: RMG Pages: 38

Brand: Yaesu Pages: 20

Brand: ZENDit Pages: 16

ATTEROTECH unBT2A

Brand: QSC Pages: 16

Brand: Maximon Pages: 16

Scantronic 734r Series

Brand: Cooper Security Pages: 80

Brand: Extron electronics Pages: 40

i.AM.Radio Transmitter

Brand: Radio Systems Pages: 12

Brand: Target Pages: 17

Brand: RCF Pages: 4

SPACEMAKER 05GP005

Brand: GE Pages: 24

Brand: KanexPro Pages: 22

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands