Barrett 2030 Operating And Installation Manual Download Page 24 | Manualshive

Page: 24 / 208

background image

BARRETT 2030 HF SSB TRANSCEIVER

24 of 208

Barrett Selective Calling System

General

In addition to the use of the transceiver in simple voice mode to call other stations
there are several different types of Selective Calling systems available.

The calling systems available for the Barrett 2030 transceiver are listed below:-

International

A four and six digit Selective Call system, fully interoperable with the UN format
published in September 2004 and fully backwards compatible with all previous
Barrett 4 digit Selcall protocols.
Includes Selcall, Beacon Call, Pagecall (SMS) call, transceiver lock call and RFDS
tone calls.

Also if the options are fitted to the transceiver it includes:-

GPS calls, used to either transmit your position to another station or request

the position of another station fitted with the GPS option and receiver.

Telcalls for direct dial telephone number calling using base stations with

telephone interconnect facilities.

Person to person secure calls

OEM 1

A four and six digit Selective Call system compatible with other major HF
manufacturers including those using encryption. Includes Selcall, Telcall, Beacon
Call, Emergency call, Pagecall and GPS call.

CCIR

A four digit Selective Call system as specified by CCIR-493.
Includes Selcall, Beacon Call, Pagecall (SMS) call and tone calls.
Also, if the options are fitted to the transceiver, it includes:-

GPS calls, used to either transmit your position to another station or request

the position of another station fitted with the GPS option and receiver.

Telcalls for direct dial telephone number calling using base stations with

telephone interconnect facilities.

«
...
22
23
24
25
26
...
»

Summary of Contents for 2030

















































































































































































































Reviews:

No comments

Related manuals for 2030

Brand: u-blox Pages: 2

Brand: R.V.R. Elettronica Pages: 12

Brand: Tiviar Pages: 72

Brand: M-system Pages: 3

BTL7-V50E-M P-C003 Series

Brand: Balluff Pages: 100

Brand: Patton electronics Pages: 4

Brand: C4Line Pages: 2

MSR ELECTRONIC PolyGard AT-1110

Brand: Intec Controls Pages: 17

Brand: Shure Pages: 4

LBT-PAR02 Series

Brand: Elecom Pages: 2

Brand: Epoch Pages: 17

Brand: YOKOGAWA Pages: 2

Brand: Jamara Pages: 8

UM-XSW-D0-LEN-V03-01

Brand: Swisson Pages: 16

Brand: Erreka Pages: 2

Brand: Zaxcom Pages: 34

Brand: Harman Kardon Pages: 16

Brand: M-system Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands