Barrett 2030 Operating And Installation Manual Download Page 60

Page: 60 / 208

BARRETT 2030 HF SSB TRANSCEIVER

Sending Your GPS Position to Another Station

select the channel you want to send the GPS call on. (“Beacon

Call” can be used to select the best channel)

listen for traffic on that channel, if no traffic is heard then continue.

press

the

key

select “GPS Send” with the scroll keys:-

then press the

key

enter the identification of the station you want to send your GPS

position to (see “

Entering station IDs and using the address

and telephone books”)

then press the

key

Your GPS position will is now be transmitted, wait for a revertive tone from the
remote station to confirm the call was received, if no revertive tone is heard repeat
the process or change to another channel and repeat the process.

Note:-

The GPS interface option BCO203004 must be fitted and the GPS receiver

P/N BCA20009 must be connected and receiving position information when using
the GPS call option.

60 of 208

Summary of Contents for 2030

















































































































































































































Search results

Summary of Contents for 2030

Reviews:

Related manuals for 2030

Brands by name

Popular brands

Barrett 2030, Operating And Installation Manual

Search results

Summary of Contents for 2030

Reviews:

Related manuals for 2030

Brands by name

Popular brands