Barrett 2030 Operating And Installation Manual Download Page 190 | Manualshive

Page: 190 / 208

background image

BARRETT 2030 HF SSB TRANSCEIVER

910 Automatic Tuning Mobile Antenna

- Barrett P/N BC91000

The 910 antenna plugs directly into the rear of a 2030 transceiver using the cables
supplied.

Important:-

2030 transceivers must have the 910 antenna option set during

programming.

The 910 antenna should be mounted in positions similar to those illustrated in the
diagrams below. Select a position free from excessive vibration. A bracket,
fabricated to withstand the forces and vibration that can be expected during off-road
driving, should be used to mount the antenna to the vehicle. When locating the
mounting position for the antenna ensure that the antenna body, when flexing on its
vibration mount, cannot come into contact with other parts of the vehicle. The
antenna should be mounted as far from surrounding objects on the vehicle as
possible.

190 of 208

«
...
188
189
190
191
192
...
»

Summary of Contents for 2030

















































































































































































































Reviews:

No comments

Related manuals for 2030

Brand: Uniphos Pages: 33

Brand: Camille Bauer Pages: 40

Brand: OMFB Pages: 9

Brand: S&T Pages: 13

Brand: M-system Pages: 3

Brand: EKT Pages: 8

Brand: FTE Maximal Pages: 44

Brand: DB Elettronica Telecomunicazioni Pages: 19

Brand: Novus Pages: 2

AvediaPlayer r92 Series

Brand: Exterity Pages: 20

Efector 600 TADx91 Series

Brand: IFM Electronic Pages: 25

Brand: Teledyne Pages: 40

Brand: B&K Pages: 12

Brand: T+A Elektroakustik Pages: 60

Brand: V2 Pages: 20

Brand: Sole Digital Pages: 17

Brand: C4Line Pages: 2

Brand: BEKA Pages: 27

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands