Barrett 2030 Operating And Installation Manual Download Page 34

Page: 34 / 208

BARRETT 2030 HF SSB TRANSCEIVER

When Asked to Enter a Telephone Number:-

Either

enter the telephone number using the numeric keypad (a number

up to 16 digits)

if you think that telephone number is in the phone book use the

Scroll keys

to find the name and number you want to call:-

if you know the name associated with the telephone number in

the phone book press the

key and either enter the first

letter of the name you want to call using the alpha keypad and

use

the

Scroll keys

or use the

Scroll keys

to find the name you

want to call:-

press the

key and the last phone number called

will be called again.

34 of 208

Summary of Contents for 2030

















































































































































































































Search results

Summary of Contents for 2030

Reviews:

Related manuals for 2030

Brands by name

Popular brands

Barrett 2030, Operating And Installation Manual

Search results

Summary of Contents for 2030

Reviews:

Related manuals for 2030

Brands by name

Popular brands