Barrett 2030 Operating And Installation Manual Download Page 18

Page: 18 / 208

BARRETT 2030 HF SSB TRANSCEIVER

Switching on the Transceiver

Switching on the Transceiver – Without a PIN

Press

for 1 second turns transceiver on

Switching on the Transceiver – With a PIN

Press

for 1 second turns transceiver on

Enter the PIN number and press

key

The transceiver will now be switched on, if however the incorrect
PIN number was entered the following is displayed:-

This display will time out and allow the re-entry of the PIN
number. If however the PIN number is entered 10 times
incorrectly the transceiver will not allow PIN number entry for a
period of one hour displaying the following:-

Note:-

The power on PIN number would have been loaded into the transceiver

during programming if the function is in use. Refer to your network administrator.

Switching Off the Transceiver

Press

for 1 second turns transceiver off

18 of 208

Summary of Contents for 2030

















































































































































































































Search results

Summary of Contents for 2030

Reviews:

Related manuals for 2030

Brands by name

Popular brands

Barrett 2030, Operating And Installation Manual

Search results

Summary of Contents for 2030

Reviews:

Related manuals for 2030

Brands by name

Popular brands