Barrett 2030 Operating And Installation Manual Download Page 71

Page: 71 / 208

BARRETT 2030 HF SSB TRANSCEIVER

Scanning with the Tunable Receiver

The receiver can scan any range of frequencies from 250 kHz to 30 MHz with a
frequency step down to 10 Hz.

Setting up Scan Frequencies

To set up the frequency scan parameters, enter the tuning receiver mode, then:-

Press

the

key for two seconds until the following is

displayed:-

Enter a new frequency, using the numeric keys, to set the lower

scan limit boundary - example below shows the lower limit set to

MHz:-

then press the

key. The newly entered frequency will be

displayed

then press the

key. The last entered upper frequency will

displayed.

71 of 208

Summary of Contents for 2030

















































































































































































































Search results

Summary of Contents for 2030

Reviews:

Related manuals for 2030

Brands by name

Popular brands

Barrett 2030, Operating And Installation Manual

Search results

Summary of Contents for 2030

Reviews:

Related manuals for 2030

Brands by name

Popular brands