Barrett 2030 Operating And Installation Manual Download Page 16 | Manualshive

Page: 16 / 208

background image

BARRETT 2030 HF SSB TRANSCEIVER

2030 Transceiver Control Head Rear View

Microphone Socket

The microphone supplied with the Barrett 2030 is inserted here.

Note:-

When the transceiver is supplied it is assembled in the one piece base

station configuration and the microphone is already fitted. If using the 2030 in the
remote control (trunk mount) configuration refer to the section “Installing the Barrett
2030 transceiver”.

Transceiver Socket

When used in a base station configuration (one piece unit, as supplied) the small
interconnect cable supplied in the kit is plugged in here with the other end into the
front of the main transceiver module. When used in the remote control (trunk
mount) configuration the longer interconnect cable supplied is used.

16 of 208

«
...
14
15
16
17
18
...
»

Summary of Contents for 2030

















































































































































































































Reviews:

No comments

Related manuals for 2030

Brand: Radionics Pages: 73

Brand: Easy wave Pages: 2

Brand: Varec Pages: 24

Brand: Icom Pages: 2

Brand: Icom Pages: 36

Brand: Icom Pages: 60

Brand: Icom Pages: 2

Brand: Icom Pages: 38

Brand: Icom Pages: 48

Brand: Icom Pages: 57

Brand: Icom Pages: 60

Brand: Icom Pages: 96

Brand: Icom Pages: 4

D-STAR ID-4100A

Brand: Icom Pages: 46

D-STAR ID-4100A

Brand: Icom Pages: 36

D-STAR ID-31A; D-STAR ID-31E

Brand: Icom Pages: 41

Brand: Icom Pages: 12

Brand: Icom Pages: 5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands