Barrett 2030 Operating And Installation Manual Download Page 23 | Manualshive

Page: 23 / 208

background image

BARRETT 2030 HF SSB TRANSCEIVER

Using the Microphone

When Using the Microphone

:-

Press and hold down the PTT (transmit) button only while talking.

Hold the microphone close to your mouth.

Speak clearly.

Use the word ‘over” to indicate you have finished speaking and
release the PTT (transmit) button.

The up/down buttons can be configured in the software to control
either the audio volume or channel up/down operations.

Note:-

The Barrett 2030 has a transmit “time-out” facility. This facility (when

programmed) allows the transmitter to be keyed in transmit mode with the PTT
(transmit) switch for a set time period, after which the transceiver switches to
receive until the PTT (transmit button is released and re-keyed. This facility
prevents the transmitter transmitting for long periods of time if, for instance, the
microphone becomes jammed between seats in a vehicle causing the PTT
(transmit) switch to be held down.

Note:-

Enabling, disabling and changing the time of the transmit timeout facility

can be set either when programming the transceiver or in the

“General ”

section of

the protected menu.

Note:-

The microphone up/down buttons can be configured for channel change or

volume control functions either when programming the transceiver or in the
“General” section of the protected menu.

23 of 208

«
...
21
22
23
24
25
...
»

Summary of Contents for 2030

















































































































































































































Reviews:

No comments

Related manuals for 2030

Brand: VIETA Pages: 66

Brand: Campbell Pages: 50

Brand: EastLink Pages: 3

Brand: Cooper Pages: 120

Brand: Icom Pages: 56

FiberLink 4160 Series

Brand: Artel Pages: 12

Brand: NPG Pages: 28

Brand: Northern Pages: 4

Brand: HBM Pages: 108

Brand: Vaisala Pages: 52

Brand: Retekess Pages: 2

Brand: Adeunis RF Pages: 9

Brand: DigitaLinx Pages: 8

Brand: AMC Pages: 4

In-Wall IR Receiver AIR6

Brand: ATON Pages: 2

RV-100 RealVision 3D

Brand: Raymarine Pages: 2

Brand: YOKOGAWA Pages: 72

Brand: cctv camera pros Pages: 9

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands