Axel WOLF 1MS User Manual Download Page 141

Page: 141 / 229

TECHNICAL APPENDIX

| TECHNICAL APPENDIX

141

16.6.1

Note about upgrading from rel 0.4.1

– 0.4.7

Starting from Wolf 2MS release 0.4.7 it is necessary to update and upgrade the complete equipment, starting from

a. File System (then)
b. Kernel (then)

c. Firmware

The correct upgrading procedure starting from firmware release 0.4.1 ore 0.4.7 is

1.  File System
2.  Kernel
3.  Firmware rel 0.5.1
4.  Firmware rel 0.6.1
5.  Firmware rel 0.6.6
6.  Firmware rel 0.6.x
7.  Firmware and Kernel 0.8.5

It is possible to retrieve the correct File System, Kernel and Firmware release asking Axel Technology support dept

[email protected]

Step 1: File System Upgrade

Step 2: Kernel Upgrade

Step 3: Firmware Upgrade from 0.4.1 to 0.5.1

Summary of Contents for WOLF 1MS






































































































































































































































Search results

Summary of Contents for WOLF 1MS

Reviews:

Axel WOLF 1MS, User Manual, Page: 141 / 229

Search results

Summary of Contents for WOLF 1MS

Reviews: